At state one I can manually change the slider value but if state two appears it should change the slider value to a fix level that is calculated by software. Moreover I also want to bind one slider to an value. Currently I am using five TK-Scales but I want to scale the HIL to a bigger size. It works okay but has a bad user experience due to the problem that all the tk-Scale sliders aren't named and also deploying on one window (you have to slide them bigger and put them to another place to use all of them). Behavior visualization In order to display the signal turning on and off the LED while the command of the circuit, we will add a scope to the model: We need to use here a scope provided by the Arduino module s blockset, which doesn t require a clock parameter input, as it is directly synchronized with the sampling period of the configuration block.ĥ Simulation/Acquisition of the signal After linking all of the previously described blocks, the Xcos schema should look like this: After hitting on the play button, the LED blinks at the same time as the following curve is plotting: Sources TP3 : Acquérir et piloter des systèmes à l'aide de cartes Arduino et d'une Toolbox Xcos dédiée TP3 Démosciences 2012.pdf Scilab / Xcos pour l enseignement des sciences de l ingénieur 2013 Scilab Enterprises chapitre «4 acquisition et pilotage de moteur (module arduino)» livret_xcos.pdf Contributors : Bruno Jofret, Scilab Enterprises, Alain Caignot, Lycée Stanislas (Paris), Vincent Crespel, Lycée Saint Louis (Paris), Marc Derumaux, Lycée Saint Louis (Paris), Cédric Lusseau, Lycée Hoche (Versailles), Gilles Moissard, Lycée Janson de Sailly (Paris), Pascal Serrier, Lycée Benjamin Franklin (Orléans) et David Violeau, Lycée Janson de Sailly (Paris).I created a HIL-ManualTesting-Prototype in Xcos using the Arduino Toolbox with an Arduino Mega as an I/O-Device. Digital input of the Arduino board In our example, we plugged the LED in the digital I/O 13 of the Arduino board, so we will have to set the pin 13 successively to 1 and 0 (electrically speaking to 5V or 0V), to turn respectively the LED on and off. As specified in the configuration blocks, the period of the signal (1s) is more than twice the period of sampling (0.1s). Type 'pol' of size 1.Ĥ Period (secs) The Period of the signal. Pulse Width (% of period) The pulse width. It must be less than Frequency*(1(Pulse_width/100)). The sampling of the signal for the blocks of the model and the time of acquisition are configured by this block: The sampling period can be specified and has to be at least twice smaller than the period of evolution of the model (NyquistShannon sampling theorem) Xcos model Simulating an input signal for the LED can be done with the Pulse Generator block PULSE_SC: By double clicking, you can adapt the following parameters: Phase delay (secs) The offset of the block. Double click on the block to let the following dialog box appear:ģ Set the Serial com port number with the information acquired in the previous step. Set up the following hardware configuration:Ģ Configuration blocks In order to acquire the Port number linked with the Arduino board, look in the bottom right corner of your Arduino IDE: Start to build the Xcos schema, with the configuration blocks: This allows a serial communication between Arduino and Scilab. First step (described in this tutorial): Soft realtime HardwareIntheLoop Second step: Code generation Another approach: (Modeling with a) State Machine Configuration/Arduino Setup In order to follow this tutorial you need the following configuration: Software: Scilab on Windows 32 or 64 bits (Version >= 5.4) Arduino toolbox Help on the installation of the module (in French): Arduino IDE Hardware: Arduino Board (driver installation on ) LED Breadboard, Resistance of 10kOhm?, wires (optional) Installation & Setup Go on the following website: And download the following file: toolbox_arduino_v3.ino (you can also download the module from this page) Plug your Arduino Board to your PC, open the Arduino IDE and flash the file toolbox_arduino_v3.ino on the Arduino Board. 1 Scilab Arduino Blinking LED Tutorial Document version 1 Yann Debray Scilab Enterprises This tutorial aims at showcasing the capabilities of Scilab for prototyping electronic embedded systems with Arduino.
0 Comments
Leave a Reply. |